The exact procedure depends on the type of bridge plug, conveyance method, and setting system being used. Bridge plugs may be conveyed using e-line, slickline, coiled tubing, tubing, or other well intervention methods.
A typical installation involves:
Setting systems vary. Depending on the application, a bridge plug may be set using an explosive setting tool, a hydraulic setting tool, or a non-explosive system such as Avalon’s NESS.
Always follow the operating procedure for the specific bridge plug and setting system being used
Permanent bridge plugs are designed for long-term or permanent wellbore isolation and well abandonments, while retrievable bridge plugs are used for temporary wellbore projects. Permanent plugs are generally removed by milling, rendering them unusable upon retrieval.
Permanent miniature bridge plugs operate the same way as standard permanent plugs, but are designed for restricted I.D applications like coiled tubing and other small-bore tubing strings.
Retrievable bridge plugs are designed for temporary well isolation and abandonment, wellhead work, snubbing operations, testing, and other tasks where the well’s service will be reinstated. Retrievable plugs are removed without milling by running a retrieving tool on tubing, coiled tubing, slickline, or wireline.
Frac plugs and bridge plugs are both used to isolate sections of a well, but they are designed for different operations. Frac plugs are designed to maintain pressure from above, while bridge plugs provide bidirectional isolation, preventing fluid pathways both above and below the wellbore.
Frac plugs are primarily used for stage isolation during hydraulic fracturing. They are typically installed between treatment stages and are often designed to be milled out, drilled out, or dissolved after the fracturing operation is complete.
Bridge plugs are mechanical barriers used to isolate sections of the well for applications such as temporary or permanent abandonment, pressure control, well repair, testing, and zone isolation.
Some frac plugs use a ball-and-seat to isolate fluid, while others use alternative sealing arrangements. Bridge plugs also vary depending on whether they are permanent, retrievable, or configured with pump-through capabilities. Some bridge plugs use an internal cork that permanently isolates the fluid.
The correct tool should be selected based on the required operation, pressure differential, well geometry, temperature, and planned removal or retrieval method.
Permanent bridge plugs block the entire wellbore cross-section, which cuts off the flow path to prevent any oil or gas from escaping. Packer plugs, however, isolate the annulus, or outer ring, between their tubing and casing so that fluids travel through the inner tubing.
Some retrievable isolation tools can be configured for more than one function. For example, Avalon’s QUP system can be configured as a bridge plug as well as for straddle, hanger, and other flow-through applications.
The appropriate configuration depends on whether the operation requires complete wellbore isolation or isolation while maintaining a flow path through the tool.
A cement plug is a section of cement placed in the wellbore to create a permanent barrier. These plugs are used in abandonment, remediation, and squeeze operations, while bridge plugs are primarily used for zone isolation in the upper and lower wellbore zones.
A bridge plug is a mechanical tool installed in the well to create an isolation barrier. Bridge plugs seal off all flow paths permanently (or until removed with a retrieval tool), while cement retainers feature an open-and-close valve.
Bridge plugs and cement plugs can sometimes be used as part of the same well program, but each performs a different function.
A retrievable bridge plug is a mechanical well isolation tool designed to create a temporary barrier in a wellbore that can later be released and removed. These plugs were designed to prevent worksites from incurring the unnecessary cost, time, labour, and equipment to mill out conventional bridge plugs when temporary pauses on well projects are resumed.
The Quinn Ultimate Packer bridge plug from Avalon Research can be sealed and reopened at a much lower cost, and it reduces the risk of damaging the well or compromising the safety of workers. It can also be rebuilt in the field for subsequent operations.
The QUP bridge plugs can be deployed using all conventional explosive and non-explosive setting systems and retrieval methods, and are compatible with slickline, E-line, and coil tubing.
Bridge plugs are used to create a mechanical barrier that isolates one section of a wellbore from another. Depending on the type of bridge plyg and operation, they are used for:
Cutting off the flow paths allows pressure and fluid movement to be controlled while other work is performed, preventing hazards like gas leaks.
For more inquiries regarding Avalon’s QUP and custom bridge plugs, get in touch with our team through our Contact form.
Contact ⎯